Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Roofing: The San Antonio Owner’s Guide
If you have a Barrette roof product that’s failing, we stock and install Barrette-compatible roofing materials across San Antonio, with most repair jobs running $400 to $1,800 and full replacements landing between $8,000 and $20,000 depending on the product line and roof size. You’ll typically notice the problem first as a leak near a penetration point, a loose or lifted panel, or granules collecting in your gutters after every rain. Barrette is a materials manufacturer, not an installer, so the parts on your roof were put there by whoever built or last serviced your home – and the failure you’re seeing is usually a combination of age, Texas weather, and installation details that didn’t account for San Antonio’s specific climate patterns.
We’re an independent San Antonio roofing and remodeling company. We’re not affiliated with Barrette, but we work with their products regularly and know the compatibility quirks, the failure points, and the right fix for each line they make. If you’re looking for someone who can actually identify what’s on your roof, source the correct part, and install it properly, you’re in the right place.
Which Barrette Models This Applies To
Barrette manufactures several roofing-adjacent product lines rather than a single shingle series, and the part you need depends on which product is failing. The most common Barrette roofing materials we see on San Antonio homes include their ridge cap systems, eave and drip edge profiles, and the flashing and vent accessory lines. If you look at the underside of a removed piece or check your original installation paperwork, you’ll usually find a stamped product code – Barrette embosses model numbers on aluminum edge products, which makes matching simple. If the stamp has worn off, measure the profile width and lip depth; Barrette’s profiles are dimensionally specific, and a mismatch with an off-the-shelf big-box substitute will leave gaps that invite water intrusion.
On the OEM versus aftermarket question: for structural pieces like ridge caps and drip edge, we recommend matching the Barrette profile exactly. Aftermarket equivalents are available and can be cheaper up front, but the gauge thickness and pre-painted finish quality vary enough that a mismatched piece will look wrong and fail faster in San Antonio’s UV-heavy summers. For accessory parts like vent screens and closure strips, quality aftermarket is fine, and we’ll tell you honestly which way to go. We also stock compatible parts for KraftMaid, Cambria, and Silestone products if you’re addressing multiple items on the property at once.
Styles & brands we work with
Signs Your Barrette Roofing Is Failing
- Water staining on ceilings or walls after rain. This usually traces back to failed flashing at penetrations – vents, chimneys, or skylights – where the Barrette flashing has pulled away from the roof surface or corroded through at a seam. The leak may not appear directly under the failure point, since water travels along rafters before dripping.
- Loose, lifted, or curling drip edge along the eaves. San Antonio’s springtime winds, combined with the thermal expansion our hot summers cause, work metal edges loose over time. A lifted edge lets water run behind the fascia and into the soffit, where the damage is invisible until the wood starts swelling or staining.
- Granules from ridge caps accumulating in gutters. Barrette ridge caps shed granules as the asphalt surface ages, but excessive granule loss after a recent hailstorm or within the first five years of installation is a warning sign of material fatigue or improper nailing. San Antonio’s hail season is real, and granule loss is often the first visible casualty.
- Rust or white oxidation streaks on metal edge products. Barrette’s aluminum profiles are coated for corrosion resistance, but once the coating is scratched during installation or abraded by wind-blown debris, the exposed metal oxidizes. Left alone, that oxidation works under the coating and eats the profile from the inside out.
- Visible gaps at ridge lines or valleys where pieces should overlap. Thermal cycling – the repeated expansion and contraction of a San Antonio summer followed by January cold snaps – gradually works fasteners loose and shifts the Barrette components. A gap of even a quarter inch is an open invitation for wind-driven rain to walk straight into the attic.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Barrette-specific roof repair in San Antonio, expect to pay between $400 and $1,800 depending on what’s failed and how much access is required. A simple drip edge replacement on a single-eave ranch home runs $400 to $800. Ridge cap replacement on a standard single-story home typically lands between $800 and $1,500. Flashing work around a chimney or skylight, where we’re removing old material, checking the substrate for rot, and rebuilding the penetration correctly, runs $600 to $1,800. Interior drywall repair from the leak is separate and priced on inspection.
If the damage is extensive enough that the roof itself needs replacement, a full job in San Antonio runs $8,000 to $20,000 depending on square footage, roof pitch, and material choice. You get a written line-item price before we start – never a verbal estimate that grows on the final bill – and the work is covered under our 365-Day Done Right Promise. If anything we touched isn’t right within a year of completion, we fix it at no cost to you.
DIY or Call Us?
What you can safely do yourself: inspect from the ground with binoculars, look for lifted edges, missing granules, or visible rust, and clear your gutters so you can see what’s actually washing down. If you’re comfortable on a ladder, you can check drip edge condition at eye level. Roof work itself – even on a single-story home – is where we tell people to stop. San Antonio roofs get brutally hot, the pitch on many older homes is steeper than it looks from the yard, and a fall from a roof eave permanently changes lives. More importantly, a repair that’s done wrong doesn’t just leak; it hides the leak until the decking below is soft and the repair bill has tripled. We carry fall protection, we’ve been on thousands of San Antonio roofs, and we know what a failed Barrette installation looks like from 20 feet away.
Call us at (254) 269-5071 for an honest assessment. Isaac Pruett and the crew will tell you what’s actually wrong, what it costs, and whether it’s even worth fixing before we ever pick up a tool.
FAQs
Barrette’s aluminum edge products typically last 15 to 25 years in San Antonio conditions, while their asphalt-based ridge cap products realistically give you 10 to 18 years depending on sun exposure, hail frequency, and how well the original install was done. Expect the lower end of those ranges on west-facing roof lines where UV exposure and afternoon heat are hardest on everything.
Yes, in most cases a failed Barrette component – flashing, drip edge, a section of ridge cap – can be repaired as a spot job without touching the rest of the roof. The exceptions are when the decking underneath has rotted from long-term water exposure, or when the failure is widespread enough that chasing individual pieces becomes more expensive than a roof replacement. We’ll give you an honest read at (254) 269-5071.
Most Barrette component repairs are done in a single visit, typically 2 to 5 hours depending on access and whether we find hidden decking damage that needs addressing. Ridge cap replacement on a standard home is usually a half-day job. Full roof replacements take 2 to 4 days for most San Antonio homes.
We stock the most common Barrette profiles and accessory parts on our trucks – standard drip edge sizes, common ridge cap configurations, and universal flashing components. For odd sizes or discontinued profiles, we source directly through our material partnerships, which usually adds a day or two to the job. Call (254) 269-5071 and we’ll confirm what we have on hand for your specific roof.
Written by Isaac Pruett, Owner, Mason Remodeling Co San Antonio at Mason Remodeling Co San Antonio, serving San Antonio and nearby areas.
